diesel centrifugal firewater pump system system consists of:(1) skid mounted 625 GPM (2837 ltr/min) @ 230 ft head Mather & Platt c/steel centrifugal pump, size 5"/6" CMBB, serial #690603/1, 2000 rpm, packed gland on shaft, driven by a Leyland diesel engine, unit # CPU-3836, type PU401/21/3, engine # 911288, type UE401/113/3, tappet clearance 020" cold, injection 26 deg before top dead center, firing order 153624, exhaust with a silencer,(1) electric driven back up pump, 625 GPM (2837 ltr/min) @ 230 ft head Mather & Platt c/steel centrifugal pump, size 5"/6" E-NE-B, serial # 690602/1, 3000 rpm, packed gland on shaft, direct driven by 60 hp, 3/50/380/420 volt, 2940 rpm motor,(1) Jockey pump with gauges and valves(1) control panel

Fire pump Direct Driven by John Deere Diesel engine, with controller and fuel tank.

• Ft./hd. (feet of head)

This Aquadyne 3300DST is a robust, mobile, Detroit Diesel-powered reciprocating pump built to deliver very high pressure (up to 10,000 psi) at 45 GPM. Its design makes it well-suited for clean-in-place (CIP) operations—such as high-pressure tank washing—where reliability and performance are critical. This system includes a tank pressure washing module for installation on manways to perform CIP operations.

3-step Membrane dosing/metering pump with vent screw on each pump head 1.4571 pulsation absorber 0,5 l, G 3/8’’, Element A: 1100 l/h @ max 10.5 bar Element B and C: 550 l/h @ 4.2 bar

• Volume: 1.500 cm³/rpm
• Tooth wheel pump without motor and gear box,
• order # 40/4357, against pressure max. 300 bar.

3/50/400/690 volt,

1.5 m3/hour at 150 bar 24-64 lift/minute,

2000 to 5000 cubic meter per hour triple head diaphragm pump working pressure 80 bar, max permissible working pressure 100 bar @ -196 degrees C driven by a 2-speed motor 52kw, 3/60/440/480 volt, 1770 rpm motor via a Lenze type 12.602.32.15 (5) 321 stainless steel valves,

25 Ra electropolished internal finish with a silicon carbide double mechanical seal. Viton is the elastomer material.

8" x 6" impellor. Vert split, end suction, top discharge. No motor. takes 900 HP, 3600 rpm motor. 4000 Volts.

4.0 ton/hour CE confirmed Order Number 40/6529

• Designed for: polymers
• Rated nominal output: 1.500 cm³/rpm
• Gear reducer: Flender Atb-Loher gear reducer, with propshaft, type 587, Poly coupling, type PKA 19, type H2 SH 05 A, serial number M 169 004 554-001-002, rated 15.0 kW, 720 rpm
• all mounted on carbon steel frame
• (1) spare gearbox available.

• split case single stage double suction pump
• Seals: John Crane 1-BP1D1, CF-SP-47517
• Close coupled to a General Electric Tri Clad AC motor
• Model 5K365AL205D1. Number OEGO71701
• Current: 178/89 amps
• Opto-Matic oilers. Pump and motor base mounted. Shipping dimensions

Dual bearings on shaft. No seals installed yet. (no motor)

Type SSO, Form CO.

sanitary centrifugal pump Removable front plate on pump casing for cleaning direct drive Motor: 230/460 V Pump has sealed bearings

One Lot of Twelve,(12) 2" suction, 1.5" discharge (no motors or baseplates, bare pump only )

Impeller diameter is 5.625". direct driven by a Baldor EM3615T 5HP motor Motor Model # 36G2741S268G1

submesrible centrifugal pump Designed to pump waste water light slurries and liquid manures basic model CP is designed for permanent installation in a sump

wet end size 6 x 8-15 With a mechanical seal on the 316SS shaft The pump gear box is flood oil lubricated The suction flange is 8” ANSI 150#, and the discharge flange is 6” ANSI 150#Wet section only no driver.

Number of pumps: 7 Type: self-priming Drive type: direct driven Motor: AC

direct driven by a Reliance Duty master AC motor 230/460 volts 9 amps

• Flow rate 217 ml/min

Square D explosion proof On/Off switch

• No motor with this unit.
• Flow rate 217 ml/min