Type: Filter

Subtype: Rosenmund and Cogiem

Manufacturer: 3V Cogeim

Model: Filtrodry FPP 100 SD/FM

Condition: Used

Material: Hastelloy - C276

Filtration Area: 1 m² (10.8 ft²)

Diameter: 1,200 mm (47.2 in)

• Side bottom discharge with automatic valve

Pressure: 6.9 bar (100.1 psi). Temperature: 177 °C (350.6 °F). Vacuum: Yes. Internal Finish: Ra 0.5. Agitation Seal Type: Mechanical. Jacket: Yes. Jacket Pressure: 10.4 bar (150.1 psi). Jacket Type: Half Pipe/Limpet. Jacket MOC: Stainless Steel 316. Jacket Temperature: 177 °C (350.6 °F). Agitator Cored for Heating/Cooling: Yes. Vessel Liquid Capacity: 1,500 L (400 gallons).

Type: Mixer-Ribbon & Paddle

Manufacturer: Young Industrial Machinery

Condition: Used

Material: Stainless Steel 304

Design Capacity: 0.28 m3 (10 ft3)

Operating Capacity: 0.17 m3 (6 ft3)

CS jacketed ribbon blender Internal pressure rated 3 psi @ 200 deg. F to -20 deg. F min.
Jacket is rated 60 psi @ 200 deg. F to -20 deg. F min. Blender configuration is full flat top cover with center bottom outlet. Shaft has stuffing box, ribbon design is removable, continuous double ribbon with Teflon wipers Shaft is driven through a Dodge shaft mounted reducer with a 24.7/1 gear reducer. Top cover is clamp on removable design. Top cover openings include 2-4", 1-8", 2-1", and 1 top feed/manway opening of 12"x16". Vessel is fully insulated. Center bottom outlet is approx. 6" and discharges through a knife gate into a Young motorized 2-3 hp delumper.

Vessel Pressure: 13.8 bar (200 psi). Vessel Temperature: -16.1 °C (3 °F). Ribbon Type: Double Helix. Length: 1,200 mm (48 in). Width: 559 mm (22 in). Height: 610 mm (24 in).

Type: Boiler

Subtype: Steam

Manufacturer: Burnham

Model: LN3L-150-50-G-BNM

Condition: Used

Material: Carbon Steel

Boiler Type: Firetube

Power: 111.9 kW (150 HP)

Three pass fire tube boiler

5021 MBH

MBH input 6278

Fireside heating surface area is 750 sq.ft

Firing rate is as follows: 1000 BTU Gas (MBH) =6277, 140,000 BTU/Gal. Oil (GPH) =44.8

Safety valve rated for 6000 psi

Boiler has 182, two-inch tubes

This boiler features FGR and low Nox operation with its IRI gas train

While firing natural gas, emissions levels are no greater than 30 PPM of NO x

• This boiler features 3 gas passes that extract the maximum usable heat from the fuel while maintaining optimum flow for forced draft firing
• It also has easy opening/closing doors that minimize labor and parts costs while performing routine maintenance such as cleaning and inspections

Water requirements are 6551 pounds of water or 785 gallons

Approximate weight wet is 16,251 lbs., approximate dry weight is 9,700 lbs

Capacity (Design): 2,350 kg/h (5,200 lb/h). Fuel Type: Natural Gas. Pressure: 1.03 bar (15 psi). Low NOx: Yes.

Type: Dryer-Oven

Manufacturer: Lewco

Model: NS-HSC1T

Condition: Used

Material: Carbon Steel

Capacity: 2.7 m3 (96 ft3)

Temperature: 148.9 °C (300 °F)

NFPA class A drum warming oven. designed for BOC Anhydride and acetic acid Purge time 10 minutes input 124,000BTUH at 75 psi Complete with fire protection and controls.

Heating Type: Steam. Pressure: 5.2 bar (75 psi). Air Flow Rate: 169.9 m3/h (100 CFM). Orientation: Vertical. Operational Mode: Batch.

Type: Centrifuge-Misc. & Hydraulic

Manufacturer: APV

Model: D36

Condition: Used

Material: Stainless Steel 316

Motor Power: 18.6 kW (25 HP)

Description: 38" dia x 39" L bowl, 2" feed pipe, 3" outlet

Podbielniak counter current extracting centrifuge job number 106-102 Bowl is 38" OD x 39" Long Hinged 304SS cover CS coated bottom housing Unit has a 2" feed pipe, 3" outlet on bottom housing 230/460 volt motor with VFD controller Drive dimensions are 48" x 40" x 30" high

Overall Length: 2,450 mm (96 in). Overall Width: 1,350 mm (53 in). Overall Height: 1,200 mm (48 in). Is Podbielniak: Yes.

Type: Mixer-Continuous

Manufacturer: Wahlco

Model: XN4612 B

Condition: Used

Material: Stainless Steel 321

Motor Power: 44.7 kW (60 HP)

Diameter: 1,150 mm (45 in)

twin shaft wad mill (pug mill) with a removable 304SS cover 1/8" thick lining Twin chrome plated mixing shafts, 5" diameter with chrome plated blades, with a CS compacting tapered screw discharge on the end of each shaft . Tapered screw sections are 14" diameter x 36" long, feeding a single 9 3/4" wide x 6" high 304SS lined discharge chute. With an air operated automatic wire cutter on discharge end of machine to cut extruded clay. Screw shafts driven through a 25.38 ratio shaft mounted reducer Motor rated for 230/460 Volts

Length: 1,150 mm (46 in). Orientation: Horizontal. Screw: Yes.

Type: Centrifuge-Inverting Filter

Manufacturer: Heinkel

Model: HF800.1

Condition: Used

Material: Hastelloy - C22

Basket Diameter: 800 mm (31.5 in)

Basket Depth: 340 mm (13.4 in)

• Internal Rated 0.7 PSI @ 170 degrees F.
• Electromechanical drive system
• 42" x 12' 6" frame, axial motor, 4080 mm long x 2065 mm wide x 1900 mm high

Filtration Area: 0.9 m² (9.7 ft²). Speed-RPM Maximum: 1,600. G Force: 1,138. Load Weight: 150 kg (330.7 lb). Washing: Yes.

Type: Classifier

Manufacturer: NETZSCH-CODUX

Model: CSF 170 HD

Condition: Used

Material: Carbon Steel

Air Flow Rate: 2,600 m3/h (1,550 CFM)

Diameter: 304.8 mm (12 in)

inlet Carbon Steel skid mounted High Efficiency Fine classifier 3600 RPM rotor max speed.15kW. 460 vac 35 amps Inlet size is 9", outlet is 21" x 19 " square flange. Rejects line is 5" Particle wheel has hinged door for clean out and wheel access This classifier is rated for 2000-2600 m3h, and 200/2400 kG/h Finess is rated for 3.0-4.0 (c/37um).

Particle Size (microns): 37.