• Plates are FDA approved- Non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 44 chambers.4 eye closed delivery,1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX.

• Plates are FDA approved, non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 95 plates with 44 chambers.
• 4 eye closed delivery, 1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX.

• Pharmaceutical design. This centrifuge has a clear distinction between the process area/clean room and the drive area. The processing area is free of dead space and allows for complete inspection and sterilization.
• The filter medium is installed inside the cantilever mounted screen basket.
• This centrifuge is Gas tight (over -pressure) to 0.04 bar. With feed and wash pipes, hydraulic plow with pneumatic heel cake removal system and solids discharge chute, with door lock switch.
• Internal accessories are Hastelloy C-22, Gasketing is PTFE.
• Internal appears to have a buff polish.

• Internal Rated 0.7 PSI @ 170 degrees F.
• Electromechanical drive system
• 42" x 12' 6" frame, axial motor, 4080 mm long x 2065 mm wide x 1900 mm high

Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

peeler centrifuge with a 0.12kw, 3/50/230/400 volt, 1360 rpm fan motor, discharge screw/plow driven by 2.2kw, 3/50/400 volt Ex motor, hydraulic door locking mechanism and cake thickness device driven by a hydraulic pump with a 0.75kw, 3/50/400 volt Ex motor, hinged front door, 1-200mm discharge, 1-250mm filtrate with s/steel tank, centrifuge with (1) Siemens OP37 controller, (1) s/steel GAF filter, (1) diaphragm pump, (1) 600ltr plastic tank, 900mm diameter x 1m high, (1) s/steel centrifugal pump, manufactured by SERO, type SEMA-3111-75-2.32, (1) 35ltr Schott glass reciever, (2) flow meter, (2) pneumatic valves, (1) main control panel

• Single pneumatic hydraulic ram closure mechanism. (completely pneumatic operation, no electric, good for hazardous environments).
• Recessed plate filter press, complete with (25) chambers(1) head plate,5 eye, closed delivery.
• 32mm cake thickness.

CS and plastic construction Series 55 Designed for ligth solids removal Lamella gravity settler uses counter courent flow principles to remove ligt solids faster than conventional settlers in about 1/10 the space

• design pressure internal 4 bar + full vacuum @ -29/185 degrees C,
• jacket 10 bar + full vacuum @ -29/185 degrees C,
• fixed bed design,
• 5.8-11.8 rpm shaft speed,
• driven by 18/9.9kw 3/50/415 volt 1500-750 rpm EEx de IIB T4 motor via a reduction gearbox,
• reversing agitator for discharging,
• packed gland,
• shaft with Hydraulic raise/lower mechanism, driven by a hydraulic power pack with a 4kw, 3/50/415 volt 1500 rpm EExd IIB T4 motor,
• 304L stainless steel half pipe coil jacket on straight side,
• carbon steel half pipe coil jacket on filter base,
• side discharge with hydraulic valve,
• slurry outlet with a 100/80mm SCHUF valve,
• internal wash ring/spray bar,
• weld dished top, weld flat bottom,
• 3.2m diameter x 1060mm straight side,
• side inspection manway with cover and davit,
• design code: ASME VIII DIV 1 ED.89 + ADD 90,

system includes

• (1) 340 Nm3/hr 316L stainless steel Apovac PMZK 3817 D3x6 vacuum pump skid, manufactured by Sulzer, skid includes: (1) 340 Nm3/hr 316L stainless steel vacuum pump, manufactured by Sulzer, driven by 37kW, 3/50/415 volt, 975 rpm EEx de IIB T4 motor, (1) 6.7 square meter 316L stainless steel tube and shell heat exchanger (liquid ring cooler), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 10 square meter 316L stainless steel tube and shell heat exchanger (exhaust gas cooler), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 5 square meter 316L stainless steel tube and shell heat exchanger (N2 Heater), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 190 liter 316L stainless steel pressure tank (condensate receiver), manufactured by Kasag, pressure -1/4 barg @ 50 degrees C,
• (2) 316L stainless steel centrifugal pumps, manufactured by Girdlestone, type 12CABC2G, 16 bar @ 20 degrees C, driven by 7.5kW, 3/50/415 volt, 2890 rpm EEx de IIB T4 motor,

Downflow dust collector 500 to 3,150 CFM air flow With 4 filter cartriges Housing has a hopper bottom with a manual valve designed to discharge into a pail 3600 rpm blower 3/60/230/460 motor Includes Torit digital controls

• approx 98 square meter filtration area
• fully automatic operation,
• plates supported on an overhead beam,
• 33 Lenser membrane plates and 2-end plates
• caulked and gasketed clothe
• cake thickness 50mm,
• drainage via internal 4-corner port,
• plate shifter hydraulic driven by a powerpack with a 1.1kw motor,
• powerpack for pressure mechanism with a 4kw 3/50/415 volt, 1430 rpm EEx d IIB T4 motor
• electrics are hazardous zone 1 Exd II A & B Temperature class 4 Plates Recessed: Yes. Plates Shifted By: Automatic.

• 316L stainless steel hinged front cover,
• cake discharge via a pivoting peeling device equipped with a broad peeler knife,
• cake level gauge,
• centrifuge on anti-vibration rubber mountings

• design pressure internal 4 bar + full vacuum @ -29/185 degrees C (9100 liter),
• jacket 10 bar + full vacuum @ -29/185 degrees C (165 liter),
• fixed bed design,
• 6.5-13 rpm shaft speed,
• driven by 10/6.6kw 3/50/415 volt, 1500/750 rpm EExd IIB T4 motor via a reduction gearbox,
• reversing agitator for discharging,
• packed gland,
• shaft with Hydraulic raise/lower mechanism, driven by a hydraulic power pack with a 4kw, 3/50/415 volt 1500 rpm EExd IIB T4 motor,
• side discharge with hydraulic valve,
• 304L stainless steel half pipe coil jacket on straight side,
• carbon steel half pipe coil jacket on filter base,
• slurry outlet with a 100/80mm SCHUF valve,
• weld dished top, weld flat bottom,
• 2.8m diameter x 1050mm straight side,
• internal wash ring/spray bar,
• side inspection manway with cover and davit,
• mounted on feet with load cells,
• design code: ASME VIII DIV I ED 89 + ADD 90,

system includes

• (1) 340 Nm3/hr 316L stainless steel Apovac PMZK 3817 D3x6 vacuum pump skid, manufactured by Sulzer, skid includes (1) 340 Nm3/hr 316L stainless steel PMZK 3817 D3x6 vacuum pump, manufactured by Sulzer Burkhardt, serial #52771, (1) 6.7 square meter 316L stainless steel tube and shell heat exchanger (liquid ring cooler), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 10 square meter 316L stainless steel tube and shell heat exchanger (exhaust gas cooler), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 5 square meter 316L stainless steel heat exchanger (N2 Heater), manufactured by Kasag, pressure tube side -1/4 barg @ -29/185 degrees C, shell -1/10 barg @ -29/185 degrees C, (1) 190 liter 316L stainless steel pressure tank (condensate receiver), manufactured by Kasag, pressure -1/4 barg @ 50 degrees C,
• (1) 60m3/hr @ 13.6m head 316 stainless steel centrifugal pump (P1), manufactured by Girdlestone, type 12CSD2G, serial #53451, size 80-50-175, driven by 7.5kW, 3/50/415 volt, 2890 rpm EEx de IIB T4 motor, sealless type, mounted on a baseplate,
• (1) 10m3/hr @ 26m head PFA lined centrifugal pump (P2), manufactured by Richter, type PCK/F 32-160, serial #917493/3/3, 2900 rpm, 147mm diameter impellor, driven by 5.5kW, 3/50/415 volt, 2900 rpm EEx de IIB T4 motor, mechanical seal, mounted on a baseplate

• 2000 kg/hr reverse Osmosis water purification system
• feed water pressure 4-6 barg,
• pneumatic pressure 5-6 barg,
• electric 400 volt, 3phase+E, 50Hz, 38 Amp,
• system includes

(4) 316L stainless steel/EPDM reverse osmosis cells, manufactured by Sommer + Strassburger, fabrik #222802.10.1, pressure 40 bar @ 80 degrees C (19 liter), (1) 5m3/hr @ 248.1/355.8m head 316L stainless steel inline centrifugal pump, manufactured by Grundfos, type CRNE3-23EX-P-G1-E-HQQE, serial #A98105920P11603, 6kW, 4500 rpm, 50/120 bar pressure, driven by 6kW, 3/50-60/380/480 volt, IP55 motor, (1) electric heater,

(1) UV filter,

(2) water softeners,

(1) 450 liter (total) 316L stainless steel vertical receiver, manufactured by Robert Sanderson & Sons Ltd, serial #10532, design pressure 3 barg + full vacuum @ 200 degrees C, asset #11476, weld dished top and bottom, 762mm diameter, openings top: 1-150mm, 4-50mm, 1-40mm, straight side: 1-80mm, bottom: 1-50mm,

built on control panel

• Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

Manufactured by Durco Enzinger Vertical tank horizontal Plate design, with wet cake discharge, with Slucing bar SS bolt on plate coil jacket on bottom head with bolted dished bottom with swing bolts Mounted on top is a faractioanl HP drive that turns the slucing bar that rund down the middel of the plate stack 6" diameter bottom cake discharge

• Side bottom discharge with automatic valve Agitator Cored for Heating/Cooling: Yes. Vessel Liquid Capacity: 400 gallons.

• Centritec Cell 8 single use insert centrifuge
• This type of flow centrifuge is for harvesting mammalian and insect cells in a single use insert. The system offers these advantages Single use, rapid changeover disposable, Precise servo drive system that minimizes vibration, User friendly, and low maintenance. Cells are pumped peristaltically from the bio reactor to the cell 8, Live cells can be recycled to the reactor, separation occurs in a gamma irritated disposable bladder and tubing system (Separation Insert) The process is three steps separation, isolation, and discharge. An inflatable barrier segregates cell rich material for the superannuant Min/Max Temp=2 -150 degrees C. (this machine has been modified with switches ,plc, and others to control temperature at an exact setpoint) Separation chamber volume 200 ml. Through put 6-120 L/Hr. Width 32.23 ", depth 46.86 ", height 67.99" Weight 640 kg.

• Plates are FDA approved and non gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• Approximately 38 chambers.
• 4 eye closed delivery, 1" inlet and outlets.
• Manual closure with Hydraulic Assist manufactured by SPX.

wall thickness 25 mm belt driven by 45 kw motor, 3/50/380-660 volt, 80mm feed, 300mm discharge on front door, 260mm wide x 660mm long filtrate, central lubrication system, and controls

About Equipment #99990

Some basic information here.

This is a heading 2

Features:

Check out these features.

• Feature 1

• Feature 2

  • Feature 2-a
  • Feature 2-b
  • Feature 2-c

• Feature 3

That about wraps it up. Here's an edit link.

• With Lenser polypropylene non-gasketed recessed plates type KCE (51) chambers.
• 40mm cake thickness ,corner feed with 3 eye closed delivery
• 3" top corner feed, 2" 3 corner discharge.
• 3300 psi hydraulic closing pressure.
• With US Filter/Siemens air over oil hydraulic pump with a 15 gallon oil reservoir requires 80 scfm @ 100 psi air supply.

• Manual screw closure.
• 4-eye closed delivery. Openings: 4-2".

with blower and controls With Blower mounted on the side of the filter housing rated. @ -40 to +30°C, single effect, filter resistance 8 mbar with cone bottom for discharge EEX rated Operating Voltage 230/400 Control panel mounted on side. Mounted on 4 legs.
CE-certified.

continous design, rectangular bed with two rectangular decks with 6 x drives type WA 338 - 380 V/8,804 kW/23,6 A/50Hz., 2 vibrating motors mfd by Rhewum, type FX 1000-6, serial # 9212104 and # 9212105

1. siev dia. mesh approx 6mm x 6mm, 2250mm long x 950mm wide, 2. siev dia. mesh approx 2mm x 5mm, 1350mm long x 950mm wide, 1. screen cloth dia. 1000mm wide x 1540mm long, 2. sceen cloth dia. 1000mm wide x 2540mm long, 3. screen cloth dia. 1000mm wide x 2440mm long, material of sieves and screen cloths is 1.4301. Motor data: 220-380 V/4 kW/50 Hz/ 980 rpm by 5370 kg centrifugal force, total weight 2800 kg.