Capacity (Design)
Measure
Quote Cart
Used mills for sale: particle size reduction equipment for powders, slurries and solids
Highest-ranked available inventory for this selection.
Used mills for sale: particle size reduction equipment for powders, slurries and solids
Set a numeric threshold to narrow the matching listings.
Select one or more values to narrow the current listings.
Use this setting to include or exclude equipment with this feature.
Select one or more values to narrow the current listings.
Enter a keyword to match this specification.
Enter a keyword to match this specification.
Showing 8 of 8 matching Ball.
Eccentric vibrating mill Type ESM Ball Mill Usable volumn is 5 liter maximum Total grinding tube volume is 19 liters, grinding medea volume is 15 liters 235 mm ID x 450 mm L. Unit is batch design, suitable for wet and dry grinding, with a feed grain size up to 30mm Can accept rods, balls, and pebble grinding media, comes with CS Rods. The Exciter is side mounted creating ellitical and linear vibrations
with CS heat box
Cylindrical Rod Mill,
with LP gas fired heating system
Feed line input(liquid) 1.5" diameter pipe.
Discharge port is 8" round with a 8.8" x 32" vent
Drive is by a Lincoln AC motor, Model BVJ AAF4P3TC61.
3 hp, 60 Hz. 230/460 volt
Drum is chain driven. Heating chamber is custom built with three firing bars with auto igniters and pilots(controlled separately).
Heating system designed to fire on LP gas.
Top mounted exhaust stack with automatic valve to maintain temperature is supplied
650 deg F. 2"-6" CS ball charge Gear driven by 40 HP, 3/60/220/440 volt, Phila gear reducer ratio 30.6:1. Bull and pinion gear ratio 4.85:1. Unit has Manzel fully centralized lubrication system w/6-station Manzel oil pump. W/control panel and starter box.
conical balls. Belt driven by motor via bull gear. Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm.
conical ball belt driven by motor via bull gear Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm.
CS/Ni-hard lined 650 deg F. 2"-6" CS ball charge Gear driven by 40 HP, 3/60/220/440 volt thru Falk gear reducer, ratio 32.69:1. Bull and pinion gear ratio 4.85:1. Unit has Manzel fully centralized lubrication system w/6-station Manzel oil pump W/control panel and starter box.
Plastic Lined Pilot Plant Ball mill / bead mill Water jacket on the outside of the shell, the inside of the grinding chamber is completely lined with hard plastic coating. will hold 170 kilograms of beads(media no included). Charging cover seal: has a Viton Rubber 7mm seal. Discharge cover size 3mm. The shell is enclosed in a safety cage. With mill is a Skid with the mill drive system and a control panel with a volt meter, amp meter, inverter, on/off switch, timer, timer reset, and jog button.
conical ball mill Non drive end ID= approximately 470 mm, (measured at the most narrow point) Drive end ID is approximately 465 mm. belt driven by motor via bull gear
Used mills are essential in industries where reducing solid materials to fine powders or controlled particle sizes is critical. Whether you’re grinding active pharmaceutical ingredients, pulverizing pigments, or micronizing mineral fillers, mills offer the precision and flexibility needed for modern process demands. With more than 47 years of experience, IPP provides used, surplus and secondhand milling systems from 20 global plant sites and maintains a ready-to-ship inventory of 15,000+ systems.
IPP stocks a wide range of industrial mills, including hammer mills, jet mills, ball mills, colloid mills, attrition mills, and roller mills from leading brands like Hosokawa, Fitzpatrick, Netzsch, Pallmann and WAB.
Mills must be built to handle abrasive, corrosive or sanitary materials:
Explore how to select the right mill for your process from Chemical Processing.
Search the IPP inventory or contact IPP’s grinding and milling specialists to find the right used, surplus or secondhand mill for your operation. Whether upgrading, scaling up or replacing worn systems, IPP delivers cost-effective solutions with minimal downtime.
Have questions about Mills or our services? Learn more about our products and why customers choose IPP.
