Flaker Width
Measure
Quote Cart
Used flaker drum and belt dryers for sale: solidifying and drying systems for heat-sensitive materials
Highest-ranked available inventory for this selection.
Used flaker drum and belt dryers for sale: solidifying and drying systems for heat-sensitive materials
Select one or more values to narrow the current listings.
Select one or more values to narrow the current listings.
Select one or more values to narrow the current listings.
Set a numeric threshold to narrow the matching listings.
Set a numeric threshold to narrow the matching listings.
Use this setting to include or exclude equipment with this feature.
Enter a keyword to match this specification.
Showing 24 of 24 matching Flaker Drum and Belt Dryers.
single drum flaker, with dip tray working pressure 6.9 bar max, design pressure 6.9 bar @ 170 degrees C steam heated drum with rotary unions drum speed variable from 0.7 to 7 rpm, adjustable knife discharge with removeable plastic blades (missing)
belt flaker, with Accu-Drop Pastillator and Variable Speed Drive Belt system is 60" wide x 75 feet long. With six (138" x 59" x 5'5") water collectors 190 Gallons rated for 55 degrees F. Six water spray systems, 116" x 2" OD. Hot melt is feed through a rotoform, with steam to keep hot melt in a liquid state. Shell side (Product side) rated for 400 degrees F, tube side, (steam) rated for 300-350 degrees F. Rotoform is 59" long x 3.25" diameter Main Belt is driven by a Euro drive variable-speed, with a helical reducer 3 HP gear ratio 34.26:1 Overall belt speed is from 25 FPM up to 125 FPM. (This can also be adjusted with different sprockets.) 1750 rpm. 2.77 HP, service factor 1 with output torque 892. The rated temperature range is 51-110 degrees F. Driven by a 1 hp AC motor, continuous duty TEFC. Model # DF26DT1001.54, serial # 88075 1570.07.
30" (800mm) dia x 40" (1000mm) long long chrome plate cast iron single drum flaker Totally enclosed in SS casing w/MS ribbing (not vac rated) Roll surface area: 0.5026 sq meter Fitted w/an unused replacement drum. New main roll bearings made in phosphor bronze in half bush arrangement. Applicator roll re-ground and re-chromed to original dia and Ra surface. Complete w/applicator tray. No motor or gearboxes w/this unit.
Pharmaceutical grade Top of belt is steam heated bottom is chilled water cooled variable speed, 0.75 kW 3/50/220/380V System equipped with SIHI cooling water vacuum pump driven by 2.5 kW 3/50/380V, 1430 RPM motor.
1.5m wide x 24.85m long rotoform cooling conveyor/belt Drawing Number 6530. 5m long hot water section 17.5m cooling water section Cooling water capacity: 185 GPM @ 30 psi, Hot water zone has 16 sprays x 4 runs x 0.71 gpm (45.4 gpm), Cold water zone has 49 sprays x 4 runs x 0.71 gpm (139.1 gpm), 900mm diameter tension drum, 900mm diameter drive drum andvik Dropformer feed unit with hot oil heated weir, chain driven by 0.75 KW, 3/50/415 volt motor via varispeed gearbox. brass knife discharge, carbon steel support frame with sump tanks mounted under the belt, Flaker includes a discharge vibratory shaker for size classifacation, (3) Sihi Centrifugal cooling water pumps, Russel Finex inline water filter,
belt flaker, with Accu-Drop Pastillator and Variable Speed Drive Belt system is 60" wide x 75 feet long. With six (138" x 59" x 5'5") water collectors 190 Gallon rated for 55 degrees F Six water spray systems, 116" x 2" OD. Hot melt is feed through a rotoform with steam to keep wax in a liquid state. Shell side(product side) rated for 400 degrees F, tube side, (steam) rated for 300-350 degrees F. Rotoform is 59" long x 3.25" diameter Main Belt is driven by a Euro drive variable-speed with a helical reducer 3 HP gear ratio 34.26:1 Overall belt speed is from 25 FPM up to 125 FPM. (This can also be adjusted with different sprockets.) Overall shipping dimensions are 75" wide x 66" tall (to top of mounted pastillator) x 75' long. Belt thickness is 0.040", belt height is 48".
chrome plate drum only For use with Gouda drum flaker
Single drum flaker Grooved drums, 1/8" groove every 1" 316SS vac chamber housing. W/spare drum Roll face is grooved on 1' spacings
508mm diameter x 508mm face pilot size 316 stainless steel drum flaker 316 stainless steel jacketed feed pan with manual raise/lower mechanism carbon steel knife with a copper replaceable blade and manual adjustment 304 stainless steel discharge chute, drum openings: 2-40mm, feed pan openings: 2-25mm
Pastillator with type: ZN stainless steel dosing system (tube needle system) can be heated, rated: 100 to 200 kg/hr, unit has an endless belt 1.2 meter wide, 1 mm thick x 11.14 meter total length 4 meter working area, with 1.4541 s/steel (321s/steel) spray nozzles for belt cooling Unit has a c/steel frame covered with aluminum.
with Type ZN stainless steel dosing system (tube needle system) can be heated rated 100 to 200 KG/Hr Unit has an endless belt 1.2 meter wide, 1mm thick,x 11.14 meter total length, 4 Meter working area with 1.4541SS (321SS) spray nozzles for belt cooling Unit has a CS frame covered with aluminum
ZN stainless steel dosing system (tube needle system) can be heated, rated 100 to 200 KG/Hr. Unit has an endless belt Unit has an endless belt, 1.2 meter wide, 1mm thick,x 11.14 meter total length, 4 Meter working area with 1.4541SS (321SS) spray nozzles for belt cooling Unit has a CS frame covered with aluminum.
with (2) 20” wide water cooled chrome plated calender rolls on the belt feed end to smooth out the hot product dropping onto the chill belt Rolls are driven by a varispeed drive, one roll is 7" diameter, the other is 16" diameter Material drops onto a stainless steel water cooled belt (similar to a Sandvick). With lump breaker on the discharge end of belt to break up cooled product Chipped product drops into a 6" SS rotary airlock valve then is pneumatically conveyed to a pre-breaker.
Universal Twin Cylinder 12" x 8" lab sized dryer, flaker.
approx 28.8 square meter 301 (NICRO 12.1)/304 stainless steel enclosed horizontal belt flaker with Pastillator, 1.5m wide x 18000mm cooling length 301 (NICRO 12.1) stainless steel belt, 19250mm belt length between center of rolls, 38500mm total length of belt, 1mm belt thickness, (3) cooling zones, zone 1 = 5.5m long (3 bar @ 5-9 degrees C), zone 2 = 6m long (3 bar @ 5-9 degrees C), zone 3 = 6.5m long (3 bar @ 5-9 degrees C), (179) plastic cooling nozzles, (2) 800mm wide 304 stainless steel drums, belt enclosed in a 304 stainless steel housing, pneumatic operated belt tensioner, belt with bakelized fiber scraper blades, (1) 120mm diameter x 1.4m wide 304 stainless steel RollDrop pastillator for distributing the liquid drops onto the cooling belt, 8mm toothed rotor pitch, type 3 x 1mm, comb material TEKAPEEK, 105 degrees C, Pastillator with pneumatic operated raise/lower mechanism, belt with pneumatic operated knife discharge with a brass blade, 304 stainless steel water trays, built on controls, Thermo Scientific model MINI-11-101F weight integrator, emergency stop button and pull cord, all mounted on a Galvanised carbon steel frame, approx 20600mm total length of flaker, (1) discharge belt conveyor,
Pastillator description: The product is fed at controlled temperature onto a roller rotor, whose rim is designed with teeth having regular shape and pitch. The liquid product slips constantly between the teeth pattern; drops are gathering on the back of every tooth, thanks to the complementary comb in touch with the toothed rotor. The formed drops are then deposited on the cooled steel belt, thanks to the centrifugal and gravitational force, generating simultaneously pastilles form.
(2) 20” wide water cooled Rolls are driven by a varispeed drive, one roll is 7" diameter, the other is 16" diameter Material drops onto a stainless steel water cooled belt (similar to a Sandvick). With lump breaker on the discharge end of belt to break up cooled product
drum flaker/dryer Single drum design Drum and applicator roll cored for steam heating Drum driven by Carter gearbox, Size MF14/100340 2.71 KW @ 960 rpm belt driven by 3 KW, 3/50/415 volt, 700 rpm flameproof motor Applicator roll driven by Croft varispeed drive 316 stainless steel knife discharge with pneumatic adjustment 316 stainless steel drip tray with 316 stainless steel fume hood Openings: hood (2) 52" x 14" plastic inspection doors, 1-8"; tray 3-1".
chrome plated single drum flaker Drum pressure 0.42 bar DC thyristor controlled varispeed drive. Roll speed 10-100 rpm. Heating low pressure steam system of 0.1 bar. Doctor manual adjustable knife made of carbon steel. Drum gear driven by 4 KW, 3/50/380 volt 1440 rpm flameproof motor Drum speed 2-18 rpm. Drum and applicator roll cored for steam/cooling
301/321/316 stainless steel pilot scale horizontal belt flaker system with a pastillator size 300 x 4000mm fabrik #02.331 CE #2.02032, 321 stainless steel belt is driven by a 2.2kw motor via a 1.35kw 316 stainless steel top housing, belt tension mechanism, manually adjustable discharge scraper, belt with a 1.8 m3/hour 321 stainless steel cooling water system with 6-spray nozzles mounted on a carbon steel frame and is a stand alone unit, system also includes: (1) top mounted 321 stainless steel pastillator (drop former) with extension device for lateral retraction mechanism for cleaning 15-nozzles (1-row of 8, 1-row of 7), (1) electrically heated distribution tray (1) 0.06 m3/hour @ 80 to 100 degrees C product feed pump
belt flaker 16' long drying section
Stokes 2-roll chrome plated flaker Has cored rollers for heating and cooling Has knife discharge Fixed roll spacing Masters gearhead varispeed motor UL labelled motor
face chrome plated single drum flaker/dryer Drum working pressure 5.5 bar, speed 3 to 21 rpm, cored for steam/hot oil heating
chrome plated drum only Cast iron construction
Searching for reliable flaker drums and belts? With over 47 years of experience, 20 complete process plant sites, and 15,000+ pieces of process equipment ready to ship, IPP delivers cost-effective solutions that help manufacturers meet demanding production timelines and budgets.
Flaker drums and belts are essential drying and solidification tools used across industries including chemicals, food processing, pharmaceuticals, and specialty materials. These systems are ideal for converting wet feedstocks into dry, uniform flakes ready for further processing or packaging.
Flaker drums apply a thin film of liquid product onto a heated rotating drum, where moisture evaporates, and the dried product is scraped off into consistent flakes. Flaker belts operate similarly, using a heated conveyor belt to achieve uniform drying and flaking for products that require a gentler process.
Browse the IPP inventory or contact IPP for expert advice and pricing to secure your flaker drum or belt today. With immediate availability, you can avoid costly production delays.
Have questions about Flaker Drum and Belt Dryers or our services? Learn more about our products and why customers choose IPP.
