Height
Measure
Quote Cart
Used plastic processing equipment for sale: cost-effective solutions for injection molding, extrusion, and recycling
Highest-ranked available inventory for this selection.
Used plastic processing equipment for sale: cost-effective solutions for injection molding, extrusion, and recycling
Enter a keyword to match this specification.
Enter a keyword to match this specification.
Enter a keyword to match this specification.
Showing 25 of 34 matching Major Items.
Polymer filter continous rotary filtration system1220 SqCm active screen area9500 Cm/Hr capacity, 48000 watt oil/vapor heating capacity, with 2 heater zones. CS construction.RexRoth 11 KW power pack 3/50/500 volt 1460 Rpm. 2900 Kg Filter
diverter valve and screen changer masch #20004017,2- 110 cm2 screens screen dimensions 120mm x 0.5mm x 93mm (+0.5),230-600 kg/hr throughput, heating capacity of the 6-cartirdges is 6 x 1000 watt, Gebhard/HLP type cartridges, hydraulically driven by a Heusinger and Salmon powerpack, powerpack driven by a 11/12.7 kw,3/50/60/380/660/420/720/380/660/480/830 volt,1440/1465/1730/1755 rpm 2-speed motor, local control panel on a davit,
centrifugal dryer, for plastic pellets/granules rated 6500 Kg/H product throughput, 50 CuM/H water rate, approx 2,550 NM3/h
24" wide, wet cut, waterslide pelletizer Serial # not available Explosion proof controls, belt driven cutter head Pneumatic assist cover
Continous, plastic pellet heater Approximatly 4" diameter x 12" long chamber, 3/4" diameter jacketed discharge. Electrically heated chamber, with roatary gear pump on discharge.
24" wide, wet cut, waterslide pelletizer. Explosion proof controls, belt driven cutter head Pneumatic assist cover
Width: 24" Cutting method: Wet Pelletizer type: Waterslide Control type: Explosion proof Cutter head: Belt driven Pneumatic assist cover
Width: 24" Cutting method: Wet Pelletizer type: Waterslide Controls: Explosion proof Cutter head: Belt driven Pneumatic assist cover
50m /h" radius curved screen 149 micron mesh, (1) 30 m3/hr @ 50m head KSB centrifugal pump, type Etachrom-BC, driven by 7.5 kw, 3/50/400/690 volt 2910 rpm motor, (1) 80 GPM stainless steel hot water tank, electric heated 700mm diameter x 700mm straight side,
Type: Underwater strand pelletizer
the vertical design provides space savings and easy access to the cutter head
Designed to Process the following PET: Melt density 1.18 g/cm3, Solid density 1.34 g/cm3. Melt temperature 285-290 degrees C. at 200-500 Pas viscosity. 90 strands with a maximum through put of 6900.
Die plate design (pn# 10295462) 5,5 mm hole diameter. With a quick change cutting head
The Cutter head diameter is 162.5 mm, 30 teeth, with a 2 degree helix angle and # 2 tooth profile.
The feed rolls are timed, with a belt drive, driven by a three phase AC motor, rated for 5.5 kW.
This system requires the following utilities: Compressed air-4-6 bar. (dry and oil free), Electrical-400 volt 3 phase. Cooling water, 30 m3/h at 30 degrees C at 6 bar maximum pressure.
3" inlet x 3" outlet steam heated hot melt gear pump
Type: Underwater strand pelletizer
the vertical design provides space savings and easy access to the cutter head. Designed to Process the following PET: Melt density 1.18 g/cm3, Solid density 1.34 g/cm3. Melt temperature 285-290 degrees C. at 200-500 Pas viscosity. 90 strands with a maximum through put of 6900.Die plate design (pn# 10295462) 5,5 mm hole diameter. With a quick change cutting head.The Cutter head diameter is 162.5 mm, 30 teeth, with a 2 degree helix angle and # 2 tooth profile.The feed rolls are timed, with a belt drive, driven by a three phase AC motor, rated for 5.5 kWThis system requires the following utilities: Compressed air-4-6 bar. (dry and oil free), Electrical-400 volt 3 phase. Cooling water, 30 m3/h at 30 degrees C at 6 bar maximum pressure.
Type: Underwater strand pelletizer the vertical design provides space savings and easy access to the cutter head Designed to Process the following PET: Melt density 1.18 g/cm3, Solid density 1.34 g/cm3. Melt temperature 285-290 degrees C. at 200-500 Pas viscosity. 90 strands with a maximum through put of 6900. Die plate design (pn# 10295462) 5,5 mm hole diameter. With a quick change cutting head. The Cutter head diameter is 162.5 mm, 30 teeth, with a 2 degree helix angle and # 2 tooth profile. The feed rolls are timed, with a belt drive, driven by a three phase AC motor, rated for 5.5 kW. This system requires the following utilities: Compressed air-4-6 bar. (dry and oil free), Electrical-400 volt 3 phase. Cooling water, 30 m3/h at 30 degrees C at 6 bar maximum pressure.
Type: Underwater strand pelletizer cutter the vertical design provides space savings and easy access to the cutter head Designed to Process the following PET: Melt density 1.18 g/cm3, Solid density 1.34 g/cm3. Melt temperature 285-290 degrees C. at 200-500 Pas viscosity. 90 strands with a maximum through put of 6900. Die plate design (pn# 10295462) 5,5 mm hole diameter. With a quick change cutting head. The Cutter head diameter is 162.5 mm, 30 teeth, with a 2 degree helix angle and # 2 tooth profile. The feed rolls are timed, with a belt drive, driven by a three phase AC motor, rated for 5.5 kW. This system requires the following utilities: Compressed air-4-6 bar. (dry and oil free), Electrical-400 volt 3 phase. Cooling water, 30 m3/h at 30 degrees C at 6 bar maximum pressure.
pellet size 3.2mm x 3.2mm, 18 m3/hr water rate (max), 3-rotor screens top side mounted 0.61 m3/second blower, driven by 0.66 kw, 2850 rpm motor, agglomarator catcher, 5-sets of 4 spray nozzles, belt driven by 5.5 kw, 3/50/60/400/690 volt, 1455/1755 rpm motor,
250-500kg/hr Maag hot melt gear pump viscosity at 10/sec 70 to 3000 Pas inlet pressure 10 bar, outlet pressure 250 bar, (4) heating cartridges (1250 Watt, 415 volt), driven by 18.5 kw, 3/50/60/380/420/480 volt, 1457-1465/1740-1765 rpm mounted on a carbon steel frame,
ET Pellet line including Polymer filtration, through cutting, with quench system. Major items include: (2) 0.38m² / 25 liter 316 SSTi Auto Back Flushing filter, (2) Gneuss Model RSF250 ZP Polymer filter, continous rotary filtration system, (2) 4.0 t/h, s/steel (1.4571) BARMAG tooth wheel pumps, (3) Rieter (Automatik), USG 600 H, PET pellet mill with Rieter Die Head, (1) 29.88 m³/h 32.5m head @ 1465rpm stainless steel (1.4408) centrifugal pump, (1) 35 m³/h 30m head @ 1450rpm stainless steel (1.4408) centrifugal pump, (1) 35 m³/h 30m head @ 1450rpm cast steel (GGG40.3) centrifugal pump, (2) 4.5m³/h 25m head @ 2900rpm stainless cast steel (1.4581) magnetic (14Nm) centrifugal pumps, (2) 2664m³/h carbon steel exhaust fans, (1) 1500 liter/min stainless steel water tank system with stainless steel ribbon, (4) approx 70 liter stainless steel hopper with a stainless steel sieve insert, stainless steel top cover, welded cone bottom, mounted on a stainless steel saddle, (1) pallet with a electrical rope winch.
centrifugal dryer rotor speed 780 rpm dryer used for plastic pellets/granules. 6500 Kg/hr product throughput. 50 m3/hr water rate approx 2550 nm3/hr
centrifugal dryer for plastic pellets/granules rated 6500 Kg/H product throughput 50 CuM/H water rate approx 2,550 NM3/h 1440 u/m
centrifugal dryer for plastic pellets/granules rated 6500 Kg/H product throughput 50 CuM/H water rate approx 2,550 NM3/h 1440 u/m
centrifugal dryer, for plastic pellets/granules rated 6500 Kg/H product throughput 50 CuM/H water rate approx 2,550 NM3/h 1440 u/m
centrifugal dryer, for plastic pellets/granules rated 6500 Kg/H product throughput, 50 CuM/H water rate, approx 2,550 NM3/h 1440 u/m
centrifugal dryer, for plastic pellets/granules rated 6500 Kg/H product throughput, 50 CuM/H water rate, approx 2,550 NM3/h 1440 u/m
Used plastic processing equipment from IPP encompasses a wide range of machinery essential for the plastics industry. From injection molding machines and extruders to granulators and recycling systems, IPP offers equipment that meets the demands of various plastic manufacturing processes. With over 47 years of industry experience, IPP supplies used, surplus, and secondhand plastic processing equipment from 20 global plant sites and maintains a ready-to-ship inventory of 15,000+ process systems.
IPP stocks equipment from leading manufacturers such as KraussMaffei, Engel, Davis-Standard, and Conair, ensuring quality and reliability.
To ensure durability and compliance, plastic processing equipment is typically constructed from:
Discover how used plastic processing equipment can enhance your manufacturing efficiency at PlastiWin Capital Equipment.
Browse IPP inventory or contact IPP’s plastic equipment specialists to find the right used, surplus, or secondhand machinery for your operations. From individual machines to complete lines, IPP helps you achieve your production goals efficiently and cost-effectively.
As highlighted by EPCA, IPP is recognized as a global buyer and seller of process plants and equipment, serving industries including plastics, with a vast inventory and international presence.
Have questions about Plastics or our services? Learn more about our products and why customers choose IPP.
