Mixers - Used and Surplus Inventory | IPP

• DISHO Vacuum Mixing Dispersing and Homogenizing Unit. Vessel manufactured by Hebold, rated FV/36 psi at 356 degrees F internal; with a 24" cone bottom. It has a flanged and bolted dish top head. Vessel openings include: Top -14" manway with hinged cover, (3) 4"; (3) 1".
• Fully insulated with SS shroud over insulation. Mounted on legs with Top mounted double motion agitator with wide sweep with perforated pitched blades and side wall scrapers, and center shaft with perforated pitched blades that intermesh with counter rotating wide sweep agitator blades.
• 3/60/230/460 volt motor Vessel discharges into a horizontal DISHO homogenizing mill, multi chamber, driven by a 51 KW 3/60/230/460 volt motor. Complete skid mounted system with approx. 5 HP water seal vacuum pump, controls and stainless steel enclosure for pump and mill drive.

• truncated vertical ribbon blender system,
• classification CE Ex II 2GD T135 degrees C X,
• pressure 913mbar /0.49 barg @ -29/80 degrees C,
• 7157 liter total volume,
• Helical VM ribbon screw,
• output speed 47.5 rpm,
• 2.6m top diameter x 2.2m high x approx 1.2m bottom diameter,
• clamped dished top with hydraulic lifting device,
• bottom discharge with 316L stainless steel ball valve,

(1) Labotech discharge system with magnetic participle separator

Size 16Trough dimensions 31" x 49" x 47" deep, hinged cover w/counter balance, w/cored dispersion type mixing blades. Packing gland on shafts Shafts geared both ends and driven by Pacemaker 200/100 HP, 3/60/460 volt, 1770/885 rpm motor, Frame #449T, w/gear reducer. Output rpm on front blade 42/21, rear blade 25/125driven by 5 HP motor.

jacketed double arm mixer Shell rated atmospheric Front mixing blade 45/30 rpm, rear mixing blade 30/20 rpm x-proof motor and starter box.

240 gal (900/1400 liter)sigma blade jkt mixer. Btm discharge.1160mm wide x 810mm deep x 1160mm long. Geared both ends. W/Flander right angle gear reducer. Mixing arms speed 168/84 rpm. Btm valve pneumatically operated.

Hinged Clamped SS top cover

CS jacketed ribbon blender Internal pressure rated 3 psi @ 200 deg. F to -20 deg. F min.
Jacket is rated 60 psi @ 200 deg. F to -20 deg. F min. Blender configuration is full flat top cover with center bottom outlet. Shaft has stuffing box, ribbon design is removable, continuous double ribbon with Teflon wipers Shaft is driven through a Dodge shaft mounted reducer with a 24.7/1 gear reducer. Top cover is clamp on removable design. Top cover openings include 2-4", 1-8", 2-1", and 1 top feed/manway opening of 12"x16". Vessel is fully insulated. Center bottom outlet is approx. 6" and discharges through a knife gate into a Young motorized 2-3 hp delumper.

Double sigma blade mixer with jacketed trough. Rated atmospheric internal. Trough is jacketed on bottom 1/3 of trough. Unit has tangential sigma blades, driven one side, with packing glands on shaft. Top cover is hinged with pneumatic cylinder, rated atmospheric internal. Trough has bolted sides. Inside trough dimensions are 40" W x 36" wide x 47" deep. Chain and sprocket drive, 3 hp gearhead motor to operate tilt discharge.

• polished truncated cone mixer,
• design pressure -0.1/0.49 barg @ -29/80 degrees,
• 4500 liter useful volume,
• internal 316L stainless steel Helical screw,
• driven by 22/25kW, 3/50-60/400-230/380-220/415-440 volt, 1471/1467/1474/1767 rpm ATEX EEx de IIB T4 V6 motor,
• 2.2m top diameter x 1735mm high cone section,
• clamped top with hydraulic lifting device,
• bottom discharge with a pneumatic segment valve,
• clamped top lifting device manufactured by Servolift Gmbh, serial #10610, type POST HOIST-KM 45, max load 3750kg, electrics 4kw, 3/50/230-400 volt,

(1) Labotech discharge system,

(1) magnetic particle separator

ribbon mixers with cylindircal housing, ribbon agitator stuffing box weight motor 660 kg, inlet and outlet filters

Octagonal blender/mixer, with a Mirror Polish internal finish. Designed with GMP and sanitary construction, 625" shell diameter 615" shell length 2.5" shell thickness 250" Cone length, 2.5" cone thickness 6" bottom butterfly valve.

15 ton/hr stainless steel horizontal conical continuous mixer with integrated nozzles for adding up to 3 components into the powder, for mixing and agglomerations pocket wheel / chain (2) trunnions, additional small mixing screw on the powder outlet to add another powder for finishing

V blender openings: (2) diameter 455mm and (1) diameter 165mm driven by electrical motor Motor type HD7A Motor: 380/420 volt

twin shell blender system maximum density of 50 lbs./cu.ft Shell diameter is 54" (est.), manway diameter is 17 3/4"with air operated butterfly valve Brake supplied with motor Electrical requirements are 230/460, 3 ph, 60 hz

twin shaft wad mill (pug mill) with a removable 304SS cover 1/8" thick lining Twin chrome plated mixing shafts, 5" diameter with chrome plated blades, with a CS compacting tapered screw discharge on the end of each shaft . Tapered screw sections are 14" diameter x 36" long, feeding a single 9 3/4" wide x 6" high 304SS lined discharge chute. With an air operated automatic wire cutter on discharge end of machine to cut extruded clay. Screw shafts driven through a 25.38 ratio shaft mounted reducer Motor rated for 230/460 Volts

connected to gear reducer rated 20 PS Screw driven from btm by 11 KW, 3/50/290/500 volt, 1400 rpm motor W/pneumatic operated discharge valve. Top has 600mm manway w/cover, 1-150mm light, 1-200mm feed

weld flat top weld coned bottom approx 200mm diameter central screw,148-1400 rpm150mm bottom outlet

Jaygo vacuum dispersion and homogenizing mixer system Mixing chamber rated 20 psi and full vacuum @ 350 degree F to -20 degree F minimum. All fittings sanitary. Unit measures 20" diameter x 20" straight side x 8" cone bottom clamped dished top. Gate design agitator with teflon scraper blades 5 rpm minimum, 34 rpm maximum. Drive has automatic hydraulic lift mechanism with 24" lift capacity System includes: (1) 3 HP Nash brass vacuum pump, Model #AT34. (1) 1 HP Moyno pump, Model #IFF4SSV, driven by 1 HP Reeves varidrive. (1) approx 5 HP inline disperser. Includes all controls and power box, temperature probes and capacitance probes.

jacketed Trusioma high intensive mixer Aluminum cover Mixer max 450 rpm. Max working capacity 300 liter. 2-tier, 2-blade impellors with baffle. Hinged cover with pneumatic opening. 8" pneumatic discharge valve. switch gear cabinet.

jacketed Loedige ploughshare mixer with choppers machine #7644 behalter #1952 jacket pressure 0.5 bar @ 110 deg C (180ltr) chamber 1110mm diameter x 2960mm straight side, internal rotor with (10) plow blades and (2) end blades, blades are removable via a reduction gearbox, packed gland on shaft, c/steel jacket on straight side only. (4) 321 s/steel choppers each belt driven by a 2-speed motor 7.5 kw 3/50/230/460/380/420 volt, 2950 rpm or 8.5 kw, 3/60/440/480 volt, 3510 rpm (8) spray nozzles, openings top: 3-350mm, jacket: 6-50mm, straight side: 2-540mm wide x 400mm high inspection doors, 2-50mm (for probes), bottom: 3-300mm long x 200mm wide each with a pneumatic operated valve, 8-25mm (spray nozzles,

• Plough share mixer without jacket rated internal atmospheric mixer included 2 choppers ,two doors for bottom discharge main V-belt drive data Main drive and gear box dismantled

150 Gallon,, vertical dispersion mixing machine with jacketed vessel. Dispersall Mixer Type VP, vessel rated for Full vacuum at 4 psi. Vessel size is 33.5" diameter x 41" deep, with removable top and welded bottom. Mounted on a stand. Two top mounted planetary mixers with Teflon scrapers. One under driven high shear mixer. With Waukesha model 25 SS positive displacement pump, with mechanical variable speed drive. Pump serial # D0261137SS. Overhead gantry for top removal.

agitated jacketed disperser system Working pressure: atmospheric Temperature range: 30 - 60 degrees C (processing), 80 degrees C (washing) Tank dimensions: approx 2400mm diameter x 2450mm straight side Internal baffles on sidewall shaft 101mm diameter x 2650mm long with (4) blade 45 degree pitched paddles, bottom mounted 316L stainless steel disperser APV drive, model IDD, serial # 900877-B, belt driven by 2-speed motor 75/15 kw, 3/50/415 volt, 1475/735 rpm, mechanical seal, 600mm 316L stainless steel disperser blade, mounted on lugs, (1) stainless steel Mono Merlin rotary screw feed pump, type SAE22HIR5/H0141, serial # G306880/01, belt driven by 7.5 kw, 3/50/415 volt, 1450 rpm motor via 3.35:1 ratio gearbox, (1) stainless steel Wigbat inline high speed shearer, belt driven by 22 kw, 3/50/415 volt, 1465 rpm motor, (1) 2 cu.m/hr s/steel Grundfos centrifugal pump, type CR2-130, model C590013-9338, 2900 rpm, 93.8m head, 21 bar @ 120 degrees C (max), (1) plastic seal water tank, (1) 2.5 m3/hr stainless steel Grundfos centrifugal pump, type CR2-110-AAA, model D4255711-9625, 2900 rpm, 68m head, 16 bar @ 120 degrees C

clamped top with davit carbon steel jacket, Pneumatically operated discharge valve

Vrieco Nauta orbital screw mixer 15 PSIG @ 275 degrees F internal ASME Code stamped Internals have a 180 grit polished finish. All Welds ground smooth, and screw is also polished with a 180 grit finish With 30HP 3/60/230/460V screw drive 3HP 3/60/230/460V arm motor Dust collector: 10' 6" long, 4'10" wide, 3'4" high, weight 800lbs.

jacketed helical screw mixer/dryer internal design pressure -1/6 bar @ 220 degrees C (6300 liter) coil jacket 20 bar @ 220 degrees C (385 liter) top head jacket -1/3 bar @ 220 degrees C (180 liter) coil jacket and top head jacket are 321 stainless steel (1.4541) bolt dished top and bolt coned bottom 2m diameter kato agitator drive 750/2975 rpm mechanical seal, 321 stainless steel half pipe coil jacket on straight side and bottom cone, 321 stainless steel straight jacket on top head,mounting ring